Graphtec FC-8000-130

[Lexat]

есть плоттер Graphtec FC-8000-130
работал 2 года по отлаженной процедуре без проблем, на днях конструктора что то в нем натыкали и теперь когда отправляю задание рисовать через Cutting Master 2 на бумаге пишет U : PW 0.0. и останавливается, а когда задание резать то U : PW 0.43000 (файлы формата *.plt)
в чем может быть причина и как её устранить?

ошибки
-148:49:47 E03010 HP-GL ERROR 10 INVALID I/O OUTPUT REQUEST
-1106437:02:34 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1106682:05:00 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1106733:09:56 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1106744:10:04 E03001 HP-GL ERROR 1 INSTRUCTION NOT RECOGNIZED
-1106744:43:37 E03001 HP-GL ERROR 1 INSTRUCTION NOT RECOGNIZED
-1106759:45:46 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1106913:14:03 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1106917:03:33 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1107024:10:48 E05004 ERROR REALIGN ROLLERS
-1107024:11:01 E05004 ERROR REALIGN ROLLERS
-1107193:39:10 W06003 WARNING CROSS CUT LOAD MEDIA
-1107705:42:05 E05004 ERROR REALIGN ROLLERS
-1107705:42:22 E05004 ERROR REALIGN ROLLERS
-1107705:42:38 E05004 ERROR REALIGN ROLLERS
-1107705:42:51 E05004 ERROR REALIGN ROLLERS
-1107705:43:03 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1107877:32:03 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1107903:33:28 E05005 ERROR CROSS CUT ERROR
-1107946:41:33 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1107946:48:28 E05005 ERROR CROSS CUT ERROR
-1108019:21:33 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1108071:59:27 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1108110:32:39 E03001 HP-GL ERROR 1 INSTRUCTION NOT RECOGNIZED
-1108110:37:40 E03001 HP-GL ERROR 1 INSTRUCTION NOT RECOGNIZED
-1108134:01:57 E05005 ERROR CROSS CUT ERROR
-1108141:45:21 E05005 ERROR CROSS CUT ERROR
-1108225:25:15 E05004 ERROR REALIGN ROLLERS
-1108266:57:09 E05004 ERROR REALIGN ROLLERS
-1108266:57:37 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON
-1108352:24:14 E05004 ERROR REALIGN ROLLERS
-1108352:24:22 E01019 HARDWARE Y POSITION ALARM POWER OFF THEN ON


Настройки
FC8000 CONDITIONS      FC8000-130 Ver1.50-STD dipsw=0x01

SELECT USER : User No.1(0)
[No.1]
Media name=Indoor vinyl
TOOL=CB09U
OFFSET=0
PUNCING W = 1.0mm
SPEED=25
FORCE=17
ACCEL.=4
TOOL No.=1
OFFSET FORCE=1
CUT LINE PATTERN=0
LTYPE UP= 0.6mm
LTYPE DWN= 8.0mm
UP MODE=UP
TANGENT EMULATION=OFF
OVERCUT S.E.=0.0mm,0.0mm
D. ADJ.=OFF
X=0.00
Y=0.00

[No.2] *
Media name=(Перо)
TOOL=PEN
OFFSET=0
PUNCING W = 1.0mm
SPEED=32
FORCE=11
ACCEL.=8
TOOL No.=1
OFFSET FORCE=1
CUT LINE PATTERN=0
LTYPE UP= 0.6mm
LTYPE DWN= 8.0mm
UP MODE=UP
TANGENT EMULATION=OFF
OVERCUT S.E.=0.0mm,0.0mm
D. ADJ.=ON
X=0.00
Y=0.00

[No.3]
Media name=Outdoor vinyl
TOOL=CB09U
OFFSET=0
PUNCING W = 1.0mm
SPEED=30
FORCE=17
ACCEL.=8
TOOL No.=1
OFFSET FORCE=1
CUT LINE PATTERN=0
LTYPE UP= 0.6mm
LTYPE DWN= 8.0mm
UP MODE=UP
TANGENT EMULATION=OFF
OVERCUT S.E.=0.0mm,0.0mm
D. ADJ.=OFF
X=0.00
Y=0.00

[No.4]
Media name=Clear film
TOOL=CB09U
OFFSET=0
PUNCING W = 1.0mm
SPEED=20
FORCE=17
ACCEL.=3
TOOL No.=1
OFFSET FORCE=1
CUT LINE PATTERN=0
LTYPE UP= 0.6mm
LTYPE DWN= 8.0mm
UP MODE=UP
TANGENT EMULATION=OFF
OVERCUT S.E.=0.0mm,0.0mm
D. ADJ.=OFF
X=0.00
Y=0.00

[No.5]
Media name=Reflective film
TOOL=CB09U
OFFSET=0
PUNCING W = 1.0mm
SPEED=20
FORCE=17
ACCEL.=3
TOOL No.=1
OFFSET FORCE=1
CUT LINE PATTERN=0
LTYPE UP= 0.6mm
LTYPE DWN= 8.0mm
UP MODE=UP
TANGENT EMULATION=OFF
OVERCUT S.E.=0.0mm,0.0mm
D. ADJ.=OFF
X=0.00
Y=0.00

[No.6]
Media name=Fluorescent film
TOOL=CB09U
OFFSET=0
PUNCING W = 1.0mm
SPEED=10
FORCE=22
ACCEL.=2
TOOL No.=1
OFFSET FORCE=1
CUT LINE PATTERN=0
LTYPE UP= 0.6mm
LTYPE DWN= 8.0mm
UP MODE=UP
TANGENT EMULATION=OFF
OVERCUT S.E.=0.0mm,0.0mm
D. ADJ.=OFF
X=0.00
Y=0.00

[No.7]
Media name=Hi-reflective film
TOOL=CB15U
OFFSET=0
PUNCING W = 1.0mm
SPEED=5
FORCE=30
ACCEL.=1
TOOL No.=1
OFFSET FORCE=1
CUT LINE PATTERN=0
LTYPE UP= 0.6mm
LTYPE DWN= 8.0mm
UP MODE=UP
TANGENT EMULATION=OFF
OVERCUT S.E.=0.0mm,0.0mm
D. ADJ.=OFF
X=0.00
Y=0.00

[No.8]
Media name=(налетать)
TOOL=POUNCE
OFFSET=0
PUNCING W = 1.0mm
SPEED=30
FORCE=12
ACCEL.=4
TOOL No.=1
OFFSET FORCE=1
CUT LINE PATTERN=0
LTYPE UP= 0.6mm
LTYPE DWN= 8.0mm
UP MODE=UP
TANGENT EMULATION=OFF
OVERCUT S.E.=0.0mm,0.0mm
D. ADJ.=OFF
X=0.00
Y=0.00

[TOOLS]
TOOL WIDTH ADJ. 1-2 x,y=0.0mm,0.0mm
TOOL WIDTH ADJ. 1-3 x,y=0.0mm,0.0mm
STEP PASS=1
OFFSET FORCE=7
OFFSET ANGLE=30
TOOL SELECT COMMAND=ENABLED
TOOL DATA SORT=OFF
AREA DATA SORT=OFF
TOOL UP SPEED=AUTO
CONDITION PRIORITY=PROGRAM
INITIAL BLADE=2mm BELOW
TOOL UP MOVE=DISABLED
TOOL UP HEIGHT=0.0mm

[ARMS]
MARK SCAN MODE=OFF
NUMBER OF POINTS=2POINTS
AXIS ALIGNMENT TOOL=LIGHT P.
MARK DISTANCE x,y= 0.0mm, 0.0mm
SENSING SPEED=NORMAL
MARK TYPE=2
D. ADJ. MODE=USER
MARK DIST. ADJ.=5mm
MARK OFFSET x,y= 0.0mm, 0.0mm
MARK AUTO SCAN=ENABLED
PAPER-WEIGHT=ENABLED
SENSOR OFFSET ADJ.=0.0mm,0.0mm
MARK SIZE=20.0
SENSOR ADJUST=OFF
SENSING LEVEL(X,Y)=60,60
SENSING LEVEL2(X,Y)=70,90
FACTORY SENSOR GAIN=13
FACTORY BASE LEVEL=0
FACTORY SENSING LEVEL(X,Y)=0,0
USER SENSOR GAIN=13
USER BASE LEVEL=0
USER SENSING LEVEL(X,Y)=0,0
RM SENSOR LEVEL ADJ SELECT=DEFAULT

[AREA]
EXPAND=DEFAULT
ROTATE=OFF
MIRROR=OFF
SCALE=s

[MEDIA]
INITIAL FEED=OFF
FEED SPEED=NORMAL
AUTO PRE FEED LENGTH=1000.0mm
PAGE LENGTH=50000.0mm
PRE FEED=1000.0mm
CROSS CUT FORCE=30
ROLL SET=REAR

[INTERFACE]
[RS-232C]
BAUD RATE=9600
PARITY=NONE
DATA BIT=8 BIT
HANDSHAKE=HARDWIRE

[COMMAND]
COMMAND=GP-GL
STEP SIZE=0.100 mm
HP-GL ORIGIN=LOWER LEFT
MODEL EMULATED=7586
CIRCLE RESOLUTION=AUTO
COMMAND ":",";"=ENABLED
COMMAND "W"=TOOL UP

[Advance]
MOVE STEP=0.1mm
LANGUAGE SELECTION=English
LENGTH UNIT=METRIC
TOOL CHECK=ENABLED
MEDIA SENSOR=ENABLED
PUSH ROLLER SENSOR=ENABLED
FAN POWER=NORMAL
BEEP FOR KEY OPE.=ON

[OtherCondition]
COPY SPACE= 1.00mm